To bleed a radiator, turn your heating off and let it cool. Then open the bleed valve at the top of the radiator with a radiator key until water starts to come out, and close it again. Finally, check your boiler pressure and top it up if it has dropped.
It’s one of the simplest jobs you can do to keep your heating working well, and it’s something our engineers have been showing customers for over 30 years. Here’s the full step-by-step, plus what to do if bleeding doesn’t solve the problem.
Signs your radiators need bleeding
- The radiator is warm at the bottom but cold at the top
- You can hear gurgling or bubbling in the radiators or pipes
- Rooms take longer to warm up than they used to
- Some radiators heat up and others don’t
These are all signs of air trapped in your heating system. Air rises to the top of the radiator and stops hot water filling it.
What you’ll need
- A radiator key (available from any hardware shop), or a flat-head screwdriver for some newer valves
- An old cloth or towel
- A small tray or container to catch drips
How to bleed a radiator, step by step
- Turn your heating off and let the radiators cool. Hot water can spray out of the valve, so never bleed a radiator while the heating is on.
- Start with the radiator furthest from the boiler. If you have more than one floor, start downstairs.
- Find the bleed valve. It’s a small square or slotted valve at one of the top corners of the radiator.
- Open the valve a quarter turn. Hold a cloth underneath. You should hear a hiss as the air escapes.
- Close the valve when water appears. Once a steady trickle of water comes out with no more air, turn the valve back. Don’t overtighten it.
- Repeat for each radiator, then check your boiler pressure.
Check your boiler pressure afterwards
Bleeding radiators lets a small amount of water out of the system, so your boiler pressure will usually drop a little. This is especially noticeable on combi and system boilers, which run on a sealed, pressurised system.
Check the gauge on your boiler once you’ve finished. It should read between 1 and 1.5 bar when the heating is cold. If it’s lower, top it up using the filling loop. Our guide to why a boiler loses pressure walks you through it. Be careful not to overfill it, or you’ll end up with boiler pressure that’s too high.
If you have an older open-vented system with a tank in the loft, the system refills itself and there’s no pressure gauge to check.
Still cold after bleeding?
If you’ve bled your radiators and they’re still not heating properly, air isn’t the problem. Here’s what it usually means:
- Cold at the bottom or in the middle. This usually points to sludge, a build-up of rust and debris settling inside the radiator. It needs a system clean by an engineer.
- Constantly needing bleeding. If air keeps coming back within weeks, there may be a leak letting air in, or a problem with the pump. It’s worth getting checked.
- Some radiators always cold. Your system may need balancing, or a valve may be stuck.
- All radiators cold. The problem is likely to be with the boiler or controls. See hot water but no heating.
Noisy radiators or pipes can also be a sign of trapped air or sludge. Our guide to boiler noises explains what each sound means.
How often should you bleed your radiators?
We’d recommend bleeding your radiators at the start of each heating season, and any time you notice cold spots at the top. It’s a good habit to pair with your annual boiler service, which keeps the boiler itself safe and efficient.
Heating help across our area
If bleeding hasn’t fixed your heating, our directly employed engineers can help. We work from our main office in East Kilbride and our offices in Ayr and Kilmarnock, covering Glasgow, Johnstone, Ayr, Prestwick and right across the areas we cover.
When to call an engineer
- Radiators are cold at the bottom, even after bleeding
- You need to bleed them every few weeks
- Your boiler keeps losing pressure
- No air or water comes out of the bleed valve
- The bleed valve is damaged or won’t close
If you smell gas, leave the property and call the National Gas Emergency number on 0800 111 999.
Need a hand with your heating?
Our Gas Safe engineers are all directly employed, with no subcontractors, and there’s someone to speak to 24/7, 365 days a year.
Call our main office in East Kilbride on 01355 203 333, Ayr on 01292 833120 or Kilmarnock on 01563 594361. Or WhatsApp us on 07344081873. You can also book a service or repair online.
Frequently asked questions
Off. Let the radiators cool down first. Bleeding a hot radiator can spray scalding water.
Start with the radiator furthest from the boiler, downstairs first, then work your way back towards the boiler and upstairs.
If air keeps coming back quickly, there may be a small leak, a pump problem or a fault letting air into the system. An engineer can find the cause.
The valve may be blocked with paint or debris, or the system pressure may be very low. Check the boiler pressure first. If that’s fine, call an engineer.