When your taps run hot but your radiators stay cold, or your radiators are warm but the hot water won’t come through, the boiler itself is usually working fine. The problem is almost always with your controls, or with the part that decides whether hot water goes to your taps or your radiators.
We’ve been repairing gas boilers across Glasgow, Lanarkshire, Renfrewshire and Ayrshire for over 30 years, and we fix this fault every day in winter. Here are the checks to try first, the most likely causes of each version of the problem, and when to book a repair.
Checks to try first
Before you call anyone, try these. They solve the problem more often than you’d think:
- Check your thermostat. Turn it up a few degrees above room temperature. If it’s wireless, replace the batteries.
- Check your timer or programmer. Make sure the heating is set to come on now, and that the clock is showing the right time after any power cut.
- Check the heating dial on the boiler. On many boilers, the heating and hot water have separate temperature controls. Make sure the heating one isn’t turned down.
- Check the boiler pressure. It should be between 1 and 1.5 bar when cold. If it’s low, read our guide to why your boiler is losing pressure.
- Reset the boiler once. If there’s a fault light on, press the reset button and wait a few minutes.
Hot water but no heating
If you’ve got hot water but your radiators stay cold, the most likely causes are:
Thermostat or programmer faults
If your thermostat or programmer isn’t sending the signal to the boiler, the heating simply won’t come on. Faulty wiring, a dead thermostat or a failed receiver can all cause this.
A stuck diverter valve (combi boilers)
A combi boiler uses a diverter valve to send hot water either to your taps or to your radiators. If it sticks in the hot water position, you’ll get hot taps but cold radiators. This is one of the most common repairs we carry out on combis.
A faulty motorised zone valve (system and regular boilers)
If you have a hot water cylinder, motorised valves control whether water goes to the heating or the cylinder. When the heating valve fails, the radiators stay cold.
Pump failure
The pump pushes hot water around your radiators. If it’s failed or seized, the heating won’t circulate, even though the boiler is firing.
Airlocks or sludge
If only some radiators are cold, or they’re cold at the top, trapped air may be the problem. Bleeding your radiators can help. Radiators that are cold at the bottom usually point to sludge, which needs a system clean.
Heating but no hot water
If your radiators are warm but the hot water won’t come through, look at these causes:
A diverter valve stuck on heating
The same diverter valve can stick the other way, sending everything to the radiators and nothing to the taps.
A faulty flow sensor (combi boilers)
When you turn on a hot tap, a flow sensor tells the boiler to start heating water. If it fails, the boiler doesn’t know you want hot water.
A blocked plate heat exchanger
In harder water areas, limescale can build up in the plate heat exchanger that heats your tap water. Hot water may be lukewarm, run hot and cold, or stop altogether.
A cylinder thermostat fault (system and regular boilers)
If you have a hot water cylinder, a faulty cylinder thermostat or zone valve can stop it heating up.
How we fix it
Our Gas Safe engineers will diagnose the fault, test the controls and check the boiler’s components, then explain what’s wrong in plain terms. You’ll get a clear quote before any parts are fitted. If a part needs ordering, we arrange the follow-up visit for you.
On older boilers, a diverter valve or plate heat exchanger repair can be costly. If that’s the case, we’ll tell you honestly whether a new gas boiler would make more sense.
Heating and hot water repairs near you
Our directly employed engineers repair boilers every day from our main office in East Kilbride and our offices in Ayr and Kilmarnock. That includes Paisley, Renfrew, Kilmarnock and Stewarton, and right across the areas we cover.
When to call an engineer
- You’ve tried the checks above and nothing has changed
- The boiler is showing a fault code
- You can hear the boiler firing but the radiators or taps stay cold
- Hot water runs hot and cold
- Your boiler is making new noises
If you smell gas, leave the property and call the National Gas Emergency number on 0800 111 999.
Get your heating or hot water back
Our Gas Safe engineers are all directly employed, with no subcontractors, and there’s someone to speak to 24/7, 365 days a year.
Call our main office in East Kilbride on 01355 203 333, Ayr on 01292 833120 or Kilmarnock on 01563 594361. Or WhatsApp us on 07344081873. You can also book a repair online.
Frequently asked questions
The most common causes are a thermostat or programmer fault, a stuck diverter valve on a combi boiler, or a failed pump or zone valve. Try the simple checks first, then call an engineer.
It’s the part inside a combi boiler that sends hot water either to your radiators or to your taps. When it sticks, you lose one or the other.
Yes. If the thermostat isn’t calling for heat, because of flat batteries, a fault or the wrong setting, the boiler won’t heat your radiators.
Often, yes. But if your boiler is older and needs an expensive part, our engineers will give you an honest view on repair versus replacement.
Related: Boiler not firing up? Checks before you call an engineer